Red pepper drying with a double pass solar air heater integrated with aluminium cans | Scientific Reports

Scientific Reports volume 14, Article number: 2877 (2024) Cite this article

1309 Accesses

8 Altmetric

Metrics details

In this paper, an experimental evaluation of a newly developed flat plate double pass solar air heater combined with aluminum cans for drying red pepper was presented. The proposed solar dryer system was designed, modeled, and evaluated. Solar air heater trials were carried out using the absorber’s top and bottom plate and aluminum cans for red pepper drying at Bahir Dar, Ethiopia. To test the solar dryer, 100 pieces of red paper were obtained from the Bahir Dar region of Ethiopia for the purpose of experimentation. Microsoft Excel was used to perform statistical analysis of eleven mathematical models. The results show that the mixed-mode solar greenhouse dryer takes less time to dry red pepper than the open solar dryer. In the midday, the solar insolation reached 973 W/m2 and the minimum solar insolation was 220 W/m2 and air is expelled at a rate of 0.0383 kg/s. According to the experimental results, the dryers chamber temperature ranged from 30.9 to 54 °C, while the ambient temperature was between 22.6 and 28.2 °C. The mixed-mode double pass achieves up to 46% and 28% efficiency when used with aluminum can dryers and conventional open sun dryers, respectively. A drying rate of 0.0003395 kg/s was achieved for the open sun dryer system and 0.0000365 kg/s for the mixed mode solar dryer. Using mixed-mode and open-sun solar dryers, the logarithmic model was found to be most effective in explaining the red pepper behavior. Furthermore, a comparison was made between the experimental and predicted moisture ratios through the calculation of the coefficient of determination (R2), the reduced chi-square (X2), and the root mean square error (RMSE). The results show that the logarithmic model achieved the highest value of the correlation coefficient (R2), which was determined to be 0.9978 and 0.9989, while the logarithmic model achieved the lowest value of Chi-square (X2).

Solar drying is the oldest technological process for the preservation of food, crops, vegetables, and fruits by exposing agricultural products to the sun using solar energy. Solar heat causes the agricultural product to be dried, removing moisture (dewatering) to the desired value. Particularly, it is essential to reduce the moisture content of foods so that they can be stored for a long time1,2. As moisture content of foodstuffs is reduced, bacterial, yeast, and mold growth and reproduction are reduced, contributing to decay and minimising moisture-mediated deterioration. This method of preserving food ensures that it can be stored for a long period of time without spoiling3.

Drying techniques may be divided into four general categories based on the way of heated product open-air or natural dryers, solar drying takes place when the red pepper is exposed to the sun and wind by placing it in the filial area, on racks, or the ground. The sun directly dries red pepper by enclosing it in a clear container with a lid, allowing it to be directly exposed to the sunlight. Besides heating the air directly with solar radiation, the greenhouse effect traps heat inside the enclosure and raises its temperature. Unlike direct solar driers, indirect solar dryers heat fresh air in a separate collector from the food chamber. Direct sunlight damages foods' nutritional value, especially those that lose nutrients4,5,6.

During the warmer months, the greenhouse dryer works as a solar dryer, as well as protecting the product from rain, dust, insects, and animals. It is a simple structure, large load capacity, and relatively good thermal performance7. Direct solar greenhouse drying system (SGDS) requires only one greenhouse, while indirect solar greenhouse drying system consists of two main components: solar air collectors and greenhouses8. This study proposes a mixed-mode solar air collector consisting of a flat plate solar air collector with aluminium canes above and below the black painted absorber to increase the area of absorbing solar energy and to create turbulence.

The rest of the paper is structured as follows: Section “Related work” presents the related works. Section “Materials and methods” provides a detailed description of the proposed methodology. The experimental findings and analyses are provided in Section “Results and discussion”. Finally, the paper is concluded in Section “Conclusion and recommendation for future work”.

Authors in9 investigated a solar dryer fitted with a unique heat recovery technology, which was taken into account in the current study. The evaluation experiments were carried out at various flow rates and drying air relative humidity values.

In10, a phase change material (PCM) was introduced inside the rectangular aluminium tube utilized as the thermal absorber, and the performance of the cross-matrix absorber double-pass solar air heater (CMADPSAH) integrated with the PCM as thermal energy storage was investigated. Although, the authors didn’t mention the test materials used to evaluate the system.

The authors in11 examined the thermal performance of two counter flow double pass solar air heater (DPSAH) systems. In the first arrangement, a typical flat plate solar absorber was used, while in the second, water-filled tubular capsules were used as a sensible heat storage medium. The longitudinal installation of the tubular capsules is parallel to the airflow direction.

The authors in12 presented a newly developed Double-pass solar drier (DPSD) that was compared to a normal cabinet drier (CD) and a traditional open-air sun drying for drying red chilli in central Vietnam.

This paper presents a double pass solar air heater for a red pepper dryer which has a relatively better mass flow rate (MFR), average ambient temperature, solar radiation requirement, and size as compared to existing works.

The dryer has an active mixed mode with aluminium cane collectors, a greenhouse to hold the product being dried, and direct solar energy transmission. The fan has to be used to facilitate air circulation. The sun's rays are captured through the transparent top cover on the solar collector and greenhouse, and the black-painted absorber plate coupled with aluminium cans is used to enhance this process. For the purpose of experimentation, 100 pieces of red paper were acquired from the Bahir Dar region in Ethiopia to test the solar dryer. Climate data and measured data are shown in Table 1, while the formulas and results of analytical calculations are shown in Table 2. The solar air collector is designed according to the dryer load of a greenhouse. To calculate the drying time, 80 kg of red pepper is dried from an initial moisture content of 79% on a wet basis to a final moisture content of 10–12.5% on a dry basis in 50 h13,14.

The manufactured flat plate solar air heater (SAH) and greenhouse drier was fashioned and installed on a basic iron frame positioned at 21.4° to the south, as determined by analytic calculations and shown in Fig. 1. There is a fan installed at the exit of the greenhouse dryer A blower unit, a test duct with entrance and exit sections, and various temperature measurement devices are included in the experimental setup. The flow system consists of an entry section, a test section, an exit section, a flow meter, and a centrifugal blower13,15. Double pass solar collector setup consists of a glazing glass single layer of 1 m × 2 m size by 4 mm thickness, a black paint aluminium absorber plate 1 m × 2 m by 1.25 mm thickness integrated with aluminium cans 100 mm length, 50 mm diameter, and 2 mm thickness. As part of the experiment, temperature, airspeed, solar radiation, relative humidity, the mass of the red pepper, and the moisture content of the red pepper are measured. From September to December, the mean temperature ranges between 22.6 and 28.2 °C, and the average relative humidity ranges from 89.47 to 59.95%. The red pepper was dried at 70 °C without compromising its quality, and the final moisture content of red pepper should be between 10 and 12.5% for safe storage.

Mixed-mode solar red pepper dryer.

To select the best drying curve equation for describing the experimental data, it is important to evaluate its goodness of fit based on the deviation between the experimental values and predicted values for the mathematical models. There are two types of mathematical models: physics-based models, which begin with a physical law or model, and observation-based models, which start with experimental data16.

The initial mass of the samples of harvested red pepper and the final mass of dried red pepper were measured with the help of a weighing balance. The dried red pepper drying curves were analysed to find the most convenient moisture ratio (MR) model between the test and model values as shown in Table 315. By comparing R2, RMSE, and X2, we selected the most suitable regression model.

The maximum correlation coefficient is given by Eq. (1).

Minimum Chi-square is given by Eq. (2).

Minimum root means square error is given by Eq. (3).

The solar collector's steady-state thermal efficiency is given by Eq. (4).

The mathematical formula for expressing system efficiency is given by Eq. (5).

The experiments is conducted according to the thin-layer drying concept given by Eq. (6)

The moisture content of the red pepper is calculated using Eq. (7).

The authors assumed a 40% impeller efficiency to cater to most fans since cost and power are major considerations as the fan efficiency ranges between 30 and 70%. Authors affirm that the study complies with relevant institutional, national, and international guidelines and legislation for plant ethics.

The experiment was conducted between 2:00 and 11:00 Ethiopian local time which gets optimum day temperature between these times. The highest temperature in the greenhouse chamber was recorded to be from 30.9 to 54 °C over ambient temperature of 22.6 °C to 28.2 °C and average relative humidity from 89.47 to 59.94%. The average temperature rises over ambient during the study observed to be 18.5 °C. Solar insolation is plotted as a function of time of day in Fig. 2. The maximum value of solar insolation recorded was 973W/m2 on the first day at 6:00 h local time and a minimum of 236 W/m2 on the fourth day at 2:00 local time. Figure 3 shows maximum greenhouse temperatures were 56.7 °C at 8:00 local time on day four. This shows that the mixed-mode solar dryer has better performance than the open-air sun drying system because the temperature in the greenhouse is much more than the ambient temperature.

Variation of solar intensity with time for five days.

Average temperatures in the greenhouse drying chamber vs Local time.

During most daylight hours, the temperature inside the dryer and solar collector was much higher than the ambient temperature. Figure 4 shows the temperature variations in the ambient air, greenhouse drying chamber, greenhouse exit, and solar collector outlet.

Variation temperatures versus local time.

The greenhouse drying system was evaluated based on its solar air collector efficiency, drying rate of red peppers, moisture loss, and drying efficiency. Efficiencies of double pass flat plate solar air heaters are the ratio of the heat gained by the air leaving the collector to the incident solar energy17. The solar collector's steady-state thermal efficiency is given by Eq. (4). The bio chemical quality parameters for the red pepper are discussed in17.

The efficiency of the double pass flat plate solar air heater was calculated using average solar collector outlet temperature, ambient temperature, and solar insolation data collected within a given time interval using MFR of 0.025 kg/s as shown in Table 4.

The efficiency of the collector achieves the highest value in the afternoon. This is caused by high gains of solar energy from the sun due to a ratio of beam radiation on the tilted surface to that of the horizontal surface. The efficiency is increasing from morning time and decrease after 10:00 h. Unfortunately, in the morning time almost constant efficiency results due to weather conditions at testing time. The overall result of the double pass solar collector average efficiency was recorded as 79% which is much greater than the previous flat plate solar heater's efficiency. Making the flow of air a double pass and adding aluminium can roughness in the absorber optimizes the efficiency of the heater.

The mathematical formula for expressing system efficiency is given by Eq. (5) 18. Open-sun drying efficiency is shown in Table 5 and mixed-mode solar drying efficiency is shown in Table 6. The drying efficiency is calculated using temperature variations. The drying efficiency decreases when the drying time is increases due to reduction in the moisture level of red pepper in both drying systems. The drying efficiency was seen to be high on the first day compared to the following days in both open sun drying and mixed-mode greenhouse drying systems, with an average drying efficiency of 28% and 46% recorded at average product temperatures of 26.23 °C and 44.93 °C respectively.

According to the difference in moisture content, the drying rate is the amount of moisture removed from the red pepper per unit time. The experiments were conducted according to the thin-layer drying concept given by Eq. (6) 19. The drying rate was calculated using a mass of water removed at a specified time. Using the mixed-mode greenhouse solar dryer, 61.123 kg of moisture was removed at a drying time of 50 h and in the open sun solar dryer, 11.84 kg of moisture was removed at a drying time of 90 h from 80 and 15.5 kg mass of fresh harvested red pepper. Mixed-mode and open-sun solar dryer systems have drying rates of 0.0003395 kg/s and 0.0000365 kg/s, respectively. Figure 5 illustrates the difference between solar drying rates obtained using the mixed-mode and open-mode systems. In the mixed mode, the drying rate was observed high value compare to the open sun drying system. This shows that the moisture removal rate of red pepper of the mixed-mode drying system is faster than that of the open sun drying.

Drying rate variation between mixed-mode and open-mode solar systems.

Equation (7) is used to calculate the moisture content of the product when it is dry20. The experiment was measured by an oven dryer taking three samples. The moisture content of freshly harvested red pepper is shown in Table 7 at their initial moisture content. Fresh harvested red peppers has an average moisture content of 79%.

Figure 6 depicts an examination of moisture loss (%wb) for the sample retrieved from the mixed-mode dryer and the sun dryer comparison. Red pepper requires 50 h to remove 75.13% (wb) of moisture content using the greenhouse drier method, and 90 h to remove 77.42% (wb) of moisture content using the open sun method. The moisture loss under the mixed-mode greenhouse dryer is faster than the standard open sun drying system to attain the target moisture level of 11.5% (DB). To achieve the necessary moisture level, the mixed-mode greenhouse solar drying system took five days, while open sun drying took nine days. This experiment was carried out at the start and end of the day for a period of 9 days, as shown in Fig. 7.

Comparison of moisture loss of mixed-mode solar drying versus open sun drying.

Weight loss of red pepper under open sun versus greenhouse drying.

80 kg of fresh red peppers were used as the beginning weight for the mixed-mode solar dryer, and after five days, 19.9 kg of red peppers and 15.5 kg from the open sun dryer system were recorded, with the final mass of pepper being recorded at 3.5 kg to achieve the necessary moisture level.

As observed in Figs. 8 and 9, the experimental MR values were fitted using all eleven of the models from the OriginPro 2019b software in both the mixed-mode solar drying mode and the open sun drying mode. The lowest value of Chi-square X2 was found to be 0.00019 and 0.00014, while the logarithmic model displayed the greatest value of the correlation coefficient R2, which was determined to be 0.9978 and 0.9989. In addition, across all the mathematical models, regardless of average tray placements, the lowest root mean square error (RMSE) was 0.013265 and 0.010035, respectively.

Logarithmic model for mixed-mode solar drying.

Logarithmic model for open sun drying.

The model coefficients and constants regression analysis of natural logarithm of MR on drying time for all mixed-mode greenhouse and open-air drying systems were determined using Microsoft Excel, as shown in Tables 8 and 9, as well as the goodness of fit values for R2, X2, and RMSE. The values were found to fluctuate with temperature21,22,23,24,25,26,27,28,29,30,31,32.

For both mixed-mode solar greenhouses and sun drying of red pepper, the logarithmic model was deemed the most suitable thin layer model. On the basis of the Figures, the curves show a good correlation between the experimental and computed values of MR, where the values are distributed around a straight line. This confirms the selection of models in describing the drying behaviour of red pepper.

Table 10 presents a comparison of the performance of the proposed solar dryer system to existing systems. In comparison with previous works, the findings of this study indicate that the suggested DPSAH for drying red peppers has a better mass flow rate, improvement in the average ambient temperature, and an improved solar radiation capacity. The results show that the proposed system achieved a higher drying capability than other systems as shown by and minimizes moisture-mediated deterioration.

This paper presents the experimental evaluation of a newly designed flat plate double pass solar air heater integrated with aluminium can for red pepper drying. The following conclusions were drawn from this study:

It was observed that greenhouses achieves the optimal temperature than separate flat plate dryers and greenhouse dryers.

With the newly designed system, the maximum outlet temperature is 54 °C for an ambient temperature of 28.2 °C.

A batch of red pepper weighing 80 kg and 15.5 kg by mass, whose initial moisture content is 79% wet basis, can be dried to 11% moisture content using the proposed double pass mixed mode solar dryer and an open solar dryer system. The moisture loss rate, the drying rate, the collector efficiency, and the drying efficiency were used to evaluate the performance of the drying systems. The total dying duration of red pepper using the mixed mode greenhouse dryer system takes 50 h to remove 75.13% of moisture content and 90 h using the open sun drying technique to remove 77.42% moisture. Open sun drying yielded 0.000395 kg/s and mixed-mode greenhouse solar drying yielded 0.0000365 kg/s, respectively.

In order to select the best drying model, the R2, X2, and RMSE values were compared. A logarithmic model is appropriate for both mixed-mode and open sun drying. Solar dryers designed with aluminum cans in the absorber's top and bottom have values of R2, X2, and RMSE of 0.99, 0.00019, and 0.0132, respectively. The results of the regression shows that the newly designed system has no effect on the food quality of the red pepper.

In the future, authors hope to use deep learning methods to determine the best drying models.

The datasets generated during and/or analysed during the current study are not publicly available but are available from the corresponding author on reasonable request.

Cabinet drier

Cross-matrix absorber double-pass solar air heater

Double pass solar air heater

Mass flow rate

Moisture ratio

Phase change material

Root means square error

Correlation coefficient

Solar air heater

Chi-square

TeferaChekol, E., Paramasivam, V., Gardie, E., Dubale, H. & Selvaraj, S. K. Experimental investigation of suitable thin layer drying curve to solar maize dryer assisted for biomass back-up heater. Mater. Today Proc. 46(17), 7389–7395 (2021).

Article Google Scholar

Prakash, O. & Kumar, A. Solar greenhouse drying: A review. Renew. Sustain. Energy Rev. 29, 905–910 (2014).

Article Google Scholar

Lakshmi, D. V. N., Muthukumar, P. & Nayak, P. K. Experimental investigations on active solar dryers integrated with thermal storage for drying of black pepper. Renew. Energy 167, 728–739 (2021).

Article Google Scholar

El-Sebaii, A. A. & Shalaby, S. M. Solar drying of agricultural products: A review. Renew. Sustain. Energy Rev. 16(1), 37–43 (2012).

Article Google Scholar

Azaizia, Z., Kooli, S., Elkhadraoui, A., Hamdi, I. & Guizani, A. A. Investigation of a new solar greenhouse drying system for peppers. Int. J. Hydrogen Energy 42(13), 8818–8826 (2017).

Article CAS Google Scholar

Patil, R. & Gawande, R. A review on solar tunnel greenhouse drying system. Renew. Sustain. Energy Rev. 56, 196–214 (2016).

Article Google Scholar

Pardhi, C. B. & Bhagoria, J. L. Development and performance evaluation of mixed-mode solar dryer with forced convection. Int. J. Energy Environ. Eng. 4(1), 1–8 (2013).

Article Google Scholar

Baneshi, M., Genome, H. & Maruyama, S. Wide-range spectral measurement of radiative properties of commercial greenhouse covering plastics and their impacts into the energy management in a greenhouse. Energy 210, 118–135 (2020).

Article Google Scholar

Mortezapour, H., Rashedi, S. J., Akhavan, H. R. & Maghsoudi, H. Experimental analysis of a solar dryer equipped with a novel heat recovery system for onion drying. J. Agric. Sci. Technol. 19, 1227–1240 (2017).

Google Scholar

Sharol, A. F. et al. Evaluation on the performance of cross-matrix absorber double-pass solar air heater (CMA-DPSAH) with and without thermal energy storage material. J. Adv. Res. Fluid Mech. Therm. Sci. 70(2), 37–49 (2020).

Google Scholar

Hussein, N. F., Ahmed, S. T. & Ekaid, A. L. Effect of tubular solar absorber on performance of counter flow double pass solar air heater: Experimental and numerical studies. IJE Trans. A 35(10), 2007–2017. https://doi.org/10.5829/IJE.2022.35.10A.18 (2022).

Article Google Scholar

Banout, J. et al. Design and performance evaluation of a Double-pass solar drier for drying of red chilli (Capsicum annum L.). Sol. Energy 85(3), 506–515. https://doi.org/10.1016/j.solener.2010.12.017 (2011).

Article ADS Google Scholar

Hamdi, I., Elkhadraoui, A., Kooli, S., Farhat, A. & Guizani, A. Drying of red pepper slices in a solar greenhouse dryer and under open sun: Experimental and mathematical investigations. Innov. Food Sci. Emerg. Technol. 52, 262–270. https://doi.org/10.1016/j.ifset.2019.01.001 (2019).

Article Google Scholar

Kooli, S., Fadhel, A., Farhat, A. & Belghith, A. Drying of red pepper in open sun and greenhouse conditions. Mathematical modeling and experimental validation. J. Food Eng. 79(3), 1094–1103 (2007).

Article Google Scholar

Fernando, J. A. K. M. & Amarasinghe, A. D. U. S. Drying kinetics and mathematical modeling of hot air drying of coconut coir pith. SpringerPlus 5, 807. https://doi.org/10.1186/s40064-016-2387-y (2016).

Article CAS PubMed PubMed Central Google Scholar

Boudeau, N. & Malécot, P. A simplified analytical model for post-processing experimental results from tube bulging test: Theory, experimentations, simulations. Int. J. Mech. Sci. 65(1), 1–11 (2012).

Article Google Scholar

Pinar, H., Çetin, N., Ciftci, B., Karaman, K. & Kaplan, M. Biochemical composition, drying kinetics and chromatic parameters of red pepper as affected by cultivars and drying methods. J. Food Compos. Anal. 102, 103976 (2021).

Article CAS Google Scholar

Amedorme, S. K., Apodi, J. & Agbezudor, K. Design and construction of forced convection indirect solar dryer for drying Moringa leaves. Sch. J. Eng. Technol. 1(3), 91–97 (2013).

Google Scholar

Hossain, M. Z., Hossain, M. A., Awal, M. A., Alam, M. M. & Rabbani, A. H. M. M. Design and development of solar dryer for chilli drying. Int. J. Res. 2(1), 63–78 (2015).

Google Scholar

Rabha, D. K., Muthukumar, P. & Somayaji, C. Experimental investigation of thin-layer drying kinetics of ghost chili pepper (Capsicum Chinense Jacq.) dried in a forced convection solar tunnel dryer. Renew. Energy 105, 583–589 (2017).

Article Google Scholar

Singh, A., Sarkar, J. & Sahoo, R. R. Experimental energy, exergy, economic and exergoeconomic analyses of batch-type solar-assisted heat pump dryer. Renew. Energy https://doi.org/10.1016/j.renene.2020.04.100 (2020).

Article Google Scholar

Philip, N., Duraipandi, S. & Sreekumar, A. Techno-economic analysis of greenhouse solar dryer for drying agricultural produce. Renew. Energy 199, 613–627. https://doi.org/10.1016/j.renene.2022.08.148 (2022).

Article Google Scholar

CésarLópez-Vidaña, E., Lilia, C. A., Octavio, G., Isaac, P. & Rogelio, B. O. Thermal performance of a passive, mixed-type solar dryer for tomato slices (Solanum lycopersicum). Renew. Energy https://doi.org/10.1016/j.renene.2019.09.018 (2019).

Article Google Scholar

Lamrani, B. et al. Energy, economic analysis and mathematical modelling of mixed-mode solar drying of potato slices with thermal storage loaded V-groove collector: Application to Maghreb region. Renew. Energy 200, 48–58. https://doi.org/10.1016/j.renene.2022.09.119 (2022).

Article CAS Google Scholar

Ndukwu, M. C. et al. Energy and exergy analysis of solar dryer with triple air passage direction collector powered by a wind generator. Int. J. Energy Environ. Eng. 14, 63–77. https://doi.org/10.1007/s40095-022-00502-8 (2023).

Article CAS Google Scholar

Ndukwu, M. C. et al. Comparative experimental evaluation and thermodynamic analysis of the possibility of using degraded C15–C50 crankcase oil waste as thermal storage materials in solar drying systems. Sol. Energy 240, 408–421. https://doi.org/10.1016/j.solener.2022.05.056 (2022).

Article ADS CAS Google Scholar

Ndukwu, M. C. et al. Drying kinetics and thermo-economic analysis of drying hot water blanched ginger rhizomes in a hybrid composite solar dryer with heat exchanger”. Heliyon https://doi.org/10.1016/j.heliyon.2023.e13606 (2023).

Article PubMed PubMed Central Google Scholar

Ndukwu, M. C. et al. Analysis of the heat transfer coefficient, thermal effusivity and mathematical modelling of drying kinetics of a partitioned single pass low-cost solar drying of cocoyam chips with economic assessments. Energies 15, 4457. https://doi.org/10.3390/en15124457 (2023).

Article CAS Google Scholar

Onyenwigwe, D. I., Ndukwu, M. C., Igbojionu, D. O. & Ugwu, E. C. Mathematical modelling of drying kinetics, economic and environmental analysis of natural convection mix-mode solar and sun drying of pre-treated potato slices. Int. J. Ambient Energy https://doi.org/10.1080/01430750.2023.2182359 (2023).

Article Google Scholar

Chouicha, S. et al. Valorization study of treated deglet-nour dates by solar drying using three different solar driers. Energy Procedia 50, 907–916. https://doi.org/10.1016/j.egypro.2014.06.109 (2014).

Article Google Scholar

Atalay, H. Comparative assessment of solar and heat pump dryers with regards to exergy and exergoeconomic performance. Energy 189, 116180. https://doi.org/10.1016/j.energy.2019.116180 (2019).

Article Google Scholar

Salau, A. O., Shonkora, S. S. & Owoeye, V. A. Analysis of solar energy potential using sunshine based model. IEEE Africon https://doi.org/10.1109/africon51333.2021.9570973 (2021).

Article Google Scholar

Download references

Department of Mechanical Engineering, School of Mechanical and Chemical Engineering, Woldia University, Woldia, Ethiopia

Zigale Admass

Department of Electrical/Electronics and Computer Engineering, Afe Babalola University, Ado-Ekiti, Nigeria

Ayodeji Olalekan Salau

School of Electrical and Computer Engineering, Debre Markos Institute of Technology, Debre Markos University, Debre Markos, Ethiopia

Bimrew Mhari

School of Mechanical and Automotive Engineering, College of Engineering and Technology, Dilla University, P.O. Box 419, Dilla, Ethiopia

Ewnetu Tefera

Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences, Chennai, Tamil Nadu, India

Ayodeji Olalekan Salau

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

Z.A.: Conceptualization, Methodology, Software, Visualization, Writing—Original draft preparation. A.O.S.: Data curation, Software, Methodology and Writing—Reviewing and Editing, Validation. B.M.: Visualization, Investigation. E.T.: Reviewing, Validation.

Correspondence to Ayodeji Olalekan Salau.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and permissions

Admass, Z., Salau, A.O., Mhari, B. et al. Red pepper drying with a double pass solar air heater integrated with aluminium cans. Sci Rep 14, 2877 (2024). https://doi.org/10.1038/s41598-024-53563-6

Download citation

Received: 06 June 2023

Accepted: 01 February 2024

Published: 04 February 2024

DOI: https://doi.org/10.1038/s41598-024-53563-6

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative